Marmitek RC840 Spezifikationen Seite 56
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
To program the Fire Trouble Tones option:
1. From the Programming menu, select Tones, Fire Trb. Tones [938].
2. Select Enabled or Disabled.
1
It is not necessary to program the Telephone Trouble Tones and Fire Trouble Tones
options if the Trouble Tones option is programmed as disabled.
8.9: Tones Options
8.9.1: Tones Output
The Tones Output option enables you to determine whether the tones sounded when
arming and disarming are sounded by the control panel’s built-in siren or its built-in
speaker.
To program the Tones Output option:
1. From the Programming menu, select Tones, Tones Options, Tones Output [9391].
2. Select Siren or Speaker.
8.9.2: Speaker Volume
The Speaker Volume option determines the volume level of the tones sounded by the
speaker.
To program the Speaker Volume option:
1. From the Programming menu, select Tones, Tones Options, Speaker Vol. [9392].
2. Select High or Low.
1
It is not necessary to program the Speaker Volume option if “Siren” is selected for the
Tones Output option.
8.9.3: Keypad Selection
The Keypad Selection feature enables you to enable or disable tones sounded by
hardwire LCD keypads.
To program the Keypad Selection option:
1. From the Programming menu, select Tones, Tones Options, Keypad Sel. [9393].
2. Use the 2, 3 and 4 keys to toggle keypad tones on or off for each keypad. If the
number of the keypad appears on the display, tones will be sounded from that
keypad.
3. Press 3 when the desired setting is displayed.
1
It is not possible to disable tones for the front panel keypad (Keypad #1).
-56- © MARMITEK
- Safety Warnings 2
- Table of Contents 3
- ProGuard800™ -5 5
- Chapter One: Introduction 6
- 1.2: Specifications 7
- 1.3: System Overview 7
- 1.4: Hardware Layout 9
- Figure 1.3: Main Board 10
- ProGuard800™ -11 11
- ProGuard800™ -13 13
- 2.2: Installation Procedure 14
- ProGuard800™ -15 15
- 2.3: Back Tamper 17
- 3.1: Front Panel Layout 19
- 3.2: System Status LEDs 19
- 3.3: Front Panel Keypad 20
- 3.4: LCD Display 20
- ProGuard800™ -21 21
- 3.7: Arming/Disarming 23
- ProGuard800™ -25 25
- FuLl A r m#1234121 26
- FULL A RM ED- M A RK 26
- ProGuard800™ -27 27
- 4.1: Menu Navigation 28
- 4.2: Stop Communications 28
- 4.4: User Codes 29
- 4.5: Follow Me 31
- 4.6: Event Log 31
- 4.7: Service Menu 32
- ProGuard800™ -33 33
- ZONE #2 34
- ProGuard800™ -35 35
- 5.1: Incoming Calls 37
- 5.2: Outgoing Calls 39
- ProGuard800™ -41 41
- 6.1: Keypad Control 42
- 6.2: Keyfob Control 42
- 6.3: Telephone Control 42
- 6.4: Scheduling 43
- Table 6.1: Weekly Schedule 44
- Chapter Seven: Devices 45
- 7.4: Supervision Time 46
- 7.5: Re-Synchronization 46
- 7.6: Zones 46
- ProGuard800™ -47 47
- 7.7: Keyfobs 49
- 7.8: Keypads 50
- 7.9: Repeaters 51
- 7.10: Wireless Siren 51
- 8.1: Entry/Exit Delay 53
- 8.2: Arm on Exit 53
- 8.4: Entry Deviation 54
- 8.5: Exit Restart 54
- 8.6: Arming Tones 54
- 8.7: Home Automation Tones 55
- 8.8: System Trouble Tones 55
- 8.9: Tones Options 56
- Chapter Nine: System Options 57
- 9.4: Panic Alarm 59
- 9.5: AC Loss Delay 59
- 9.6: Display Options 60
- 9.7: PGM Output Options 61
- 9.9: “No Arm” Indication 62
- 9.10: Jamming Detection 62
- 9.11: “No Motion” Time 63
- 9.13: Vocal Messages 63
- 9.14: Installer Access 63
- 9.16: Daylight Savings 64
- 9.17: Report Fail Trouble 64
- 9.18: Cancel Alarm 64
- 9.20: Verified Fire 65
- 9.21: Battery Type 65
- Chapter Ten: Communications 66
- ProGuard800™ -67 67
- 10.3: Vocal Message Dialler 68
- ProGuard800™ -69 69
- 10.4: Remote Programming 70
- ProGuard800™ -71 71
- 10.5: Service Call 72
- 10.6: Communications Options 72
- ProGuard800™ -73 73
- 10.7: GSM Options 75
- ProGuard800™ -77 77
- ProGuard800™ -79 79
- 11.1: X-10 Overview 80
- 11.2: HA Units 80
- ProGuard800™ -81 81
- 11.3: House Code 83
- 11.4: HA Control 83
- 12.1: Initialization 84
- 12.3: Clear User Codes 84
- 12.5: Find Modules 85
- Appendix A: Menu Structure 86
- ProGuard800™ -87 87
- ProGuard800™ -89 89
- ProGuard800™ -91 91
- PIR Sensors (MS845) 93
- ProGuard800™ -95 95
- Magnetic Contact (DS831) 96
- ProGuard800™ -97 97
- Glass break Sensor (GB843) 99
- Figure B.7: GB843 (cover off) 100
- ProGuard800™ -101 101
- Smoke Detector (SD833) 102
- Keyfobs (PR811/KR814) 103
- Figure B.13: WK820 104
- Figure B.14: RC840 104
- ProGuard800™ -105 105
- Transmitter Specifications 106
- Appendix C: Event Table 107
- Appendix D: Zone Types 109
- Declaration of Conformity 111
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Marmitek RC840
(68 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern